Made of such materials as gelatin, vinyl, and rubber, flexible molds are used for producing more than one cast; they offer a much simpler alternative to piece molding when the original model is a rigid one with complex forms and undercuts. The material is melted and poured around the original positive in sections, if necessary. Being flexible, the mold easily pulls away from a rigid surface without causing damage. While it is being filled (with wax, plaster, concrete, and fibreglass-reinforced resins), the mold must be surrounded by a plaster case to prevent distortion.
The lost-wax process is the traditional method of casting metal sculpture. It requires a positive, which consists of a core made of a refractory material and an outer layer of wax. The positive can be produced either by direct modeling in wax over a prepared core, in which case the process is known as direct lost-wax casting, or by casting in a piece mold or flexible mold taken from a master cast. The wax positive is invested with a mold made of refractory materials and is then heated to a temperature that will drive off all moisture and melt out all the wax, leaving a narrow cavity between the core and the investment. Molten metal is then poured into this cavity. When the metal has cooled down and solidified, the investment is broken away, and the core is removed from inside the cast. The process is, of course, much more complex than this simple outline suggests. Care has to be taken to suspend the core within the mold by means of metal pins, and a structure of channels must be made in the mold that will enable the metal to reach all parts of the cavity and permit the mold gases to escape. A considerable amount of filing and chasing of the cast is usually required after casting is completed.
While the lost-wax process is used for producing complex, refined metal castings, sand molding is more suitable for simpler types of form and for sculpture in which a certain roughness of surface does not matter. Recent improvements in the quality of sand castings and the invention of the “lost-pattern” process (see below) have resulted in a much wider use of sand casting as a means of producing sculpture. A sand mold, made of special sand held together by a binder, is built up around a rigid positive, usually in a number of sections held together in metal boxes. For a hollow casting, a core is required that will fit inside the negative mold, leaving a narrow cavity as in the lost-wax process. The molten metal is poured into this cavity.
The lost-pattern process is used for the production by sand molding of single casts in metal. After a positive made of expanded polystyrene is firmly embedded in casting sand, molten metal is poured into the mold straight onto the expanded foam original. The heat of the metal causes the foam to pass off into vapour and disappear, leaving a negative mold to be filled by the metal. Channels for the metal to run in and for the gases to escape are made in the mold, as in the lost-wax process. The method is used mainly for producing solid castings in aluminum that can be welded or riveted together to make the finished sculpture.
Slip casting is primarily a potter’s technique that can be used for repetition casting of small pottery sculptures. Liquid clay, or slip, is poured into a plaster piece mold. Some of the water in the slip is absorbed by the plaster and a layer of stiffened clay collects on the surface of the mold. When this layer is thick enough to form a cast, the excess slip is poured off and the mold is removed. The hollow clay cast is then dried and fired.
Simple casts for pottery sculpture—mainly tiles and low reliefs—can be prepared by pressing clay into a rigid mold. More complex forms can be built up from a number of separately press-cast pieces. Simple terra-cotta molds can be made by pressing clay around a rigid positive form. After firing, these press molds can be used for press casting. Pointing
A sculpture can be reproduced by transposing measurements taken all over its surface to a copy. The process is made accurate and thorough by the use of a pointing machine, which is an arrangement of adjustable metal arms and pointers that are set to the position of any point on the surface of a three-dimensional form and then used to locate the corresponding point on the surface of a copy. If the copy is a stone one, the block is drilled to the depth measured by the pointing machine. When a number of points have been fixed by drilling, the stone is cut away to the required depth. For accurate pointing, a vast number of points have to be taken, and the final surface is approached gradually. The main use of pointing has been for the indirect method of carving.
Enlarged and reduced copies of sculpture can also be produced with the aid of mechanical devices. A sophisticated reducing machine that works on the principle of the pantograph (an instrument for copying on any predetermined scale, consisting of four light, rigid bars jointed in parallelogram form) is used in minting for scaling down the sculptor’s original model to coin size. Surface finishing
Surface finishes for sculpture can be either natural—bringing the material of the sculpture itself to a finish—or applied. Almost all applied surface finishes preserve as well as decorate. Smoothing and polishing
Many sculptural materials have a natural beauty of colour and texture that can be brought out by smoothing and polishing. Stone carvings are smoothed by rubbing down with a graded series of coarse and fine abrasives, such as carborundum, sandstone, emery, pumice, and whiting, all used while the stone is wet. Some stones, such as marble and granite, will take a high gloss; others are too coarse-grained to be polished and can only be smoothed to a granular finish. Wax is sometimes used to give stone a final polish.
The natural beauty of wood is brought out by sandpapering or scraping and then waxing or oiling. Beeswax and linseed oil are the traditional materials, but a wide range of waxes and oils is currently available.
Ivory is polished with gentle abrasives such as pumice and whiting, applied with a damp cloth.
Concrete can be rubbed down, like stone, with water and abrasives, which both smooth the surface and expose the aggregate. Some concretes can be polished.
Metals are rubbed down manually with steel wool and emery paper and polished with various metal polishes. A high-gloss polish can be given to metals by means of power-driven buffing wheels used in conjunction with abrasives and polishes. Clear lacquers are applied to preserve the polish. Painting
Stone, wood, terra-cotta, metal, fibreglass, and plaster can all be painted in a reasonably durable manner provided that the surfaces are properly prepared and suitable primings and paints are used. In the past, stone and wood carvings were often finished with a coating of gesso (plaster of paris or gypsum prepared with glue) that served both as a final modeling material for delicate surface detail and as a priming for painting. Historically, the painting and gilding of sculpture were usually left to specialists. In Greek relief sculpture, actual details of the composition were often omitted at the carving stage and left for the painter to insert. In the 15th century, the great Flemish painter Rogier van der Weyden undertook the painting of sculpture as part of his work.
Modern paint technology has made an enormous range of materials available. Constructed sculptures are often finished with mechanical grinders and sanders and then sprayed with high-quality cellulose paints. Gilding